Book Now!

 

 

This great article following next about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is quite attention-grabbing. Don't miss it.

Setting up a tub isn't precisely brain surgery, but it does call for solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably hard task. If the old tub is easily accessible, the project can move easily; if you need to open a wall to eliminate the old tub as well as place the brand-new tub, the job is much harder. In either case, the project is within a home handyman's abilities, although you will certainly need an assistant to vacate the old tub and embeded in the new one. Make certain you have actually certified yourself for the task as well as fit trying it. As opposed to hiring a service provider to take over a halfway-completed job, it is much better to consider using one prior to you start. Chances are you might require a specialist plumber to make tube connections.
This article will assist you mount a brand-new bath tub in your shower room if you have currently acquired a brand-new bathtub and also do not need to change the arrangement of your previous water supply pipes.
Your tools and product list should consist of the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Measuring tape


• Pipe Caps


 

Removing Old Taps

If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is separate the water system. After doing so, switch on the faucets to drain any type of water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the limited gain access to that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. When the faucets have been removed, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.

 

 

Suitable New Touches

If the tails of the new taps are plastic, then you will certainly need a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the tap and the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in position with the maker offered backnut. Once the faucet is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type ought to be attached to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Setting up the Bathtub

Using both wooden boards under its feet, place the bath tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the spirit level and changing the feet on the bathtub up until the spirit level checks out degree.
To set up taps, fit all-time low of the furthest versatile faucet port to the appropriate supply pipeline by making a compression join; then do the same for the various other tap.
Turn on the water supply as well as examine all joints and new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and additionally examine the overflow electrical outlet as well as the regular electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the maker's user's manual. Tiling and sealing around the tub must wait up until the bath tub has actually been used a minimum of once as this will certainly resolve it right into its final position.

 

 

Getting ready for the Setup

To start with, the sustaining structure provided with the bathroom should be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final placement.

 

 

Tiling Around the Tub

In the location where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a stiff seal, causing the water to permeate the wall in between the bath as well as the tiling, resulting in difficulties with moisture and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, as well as are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the bathtub with water before securing, to allow for the motion experienced when the tub is in usage. The sealant can break rather early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant glue and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a keen person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I assumed sharing that piece of content was worth the trouble. Are you aware of another person who is fascinated about the topic? Take a moment to share it. I praise you for your time. Visit us again soon.

Request An Estimate